Industrial Panel Boards
We are Specialised in manufacturing of
MV Panel
A medium voltage switchgear is a set of electrical equipment enclosed in a predominantly metal structure. This centralized set includes a variety of switches, transformers, fuses and circuit breakers. Electrical panels are used to better protect, control and separate electrical equipment from each other
MCC Panel
MCC Panel (Motor Control Center) that is a device used to control and actualize the performance of an electric motor. These MCC Panels are offered in a wide variety such as compartmentalized with ACB, MCCB, SFU, DOL, ATS, Star Delta Starters & VFD STARTERS.
PMCC Panel
Our range of Power Cum Motor Control Centre (PMCC) is used to distribute the power through the panels. It is then distributed to the different motor loads located at various parts of the factory system.
Auto/Manual Synchronising Load Sharing Panel
A load sharing system will continuously adjust the engine speed settings to avoid fluctuations in the average power that is generated. The gen-sets are bundled as if they were one by synchronizing the electrical output torque. This way they will behave as if they are mechanically tied together.
PCC Panel
Auto Main Failure Panel to restore power during power failures and are installed in between the generators and main power supply. When the main supply failure occurs, the panel disconnects the main from the load, activates the generator and shifts load to generator output
PDB Panel
Power Distribution Board is used for electrical Power Distribution. In this ACB, MCCB, SDF, MCB etc are the main equipments. This receives supply from PCC. Power Distribution Board offers Isolation and Short Circuit as basic protections. Other Protections like over current, Earth Fault, Earth Leakage etc are offered on case to case basis.
APFC Panel
APFC is an automatic power factor control panel which is used to improve the power factor, whenever required, by switching ON and OFF the required capacitor bank units automatically.
AMF Panel
Auto Main Failure Panel to restore power during power failures and are installed in between the generators and main power supply. When the main supply failure occurs, the panel disconnects the main from the load, activates the generator and shifts load to generator output.
Fire Panel | Fire Alarm Panel
An alarm control panel is the central hub of a security set up. All of a user's security devices will connect with the control panel to alert the user when they are activated. An alarm control panel can also be used to activate any home automation
SSB Panel
APFC is an automatic power factor control panel which is used to improve the power factor, whenever required, by switching ON and OFF the required capacitor bank units automatically.
LT Panel for solar power plant.
LT Panel is an electrical distribution board that receives power from an solar panels and distributes the same to various electronic devices and distribution boards
LT Panel
Main LT panels are considered the heart of the electrical supply system in any installed network of electrical distribution. The secondary side of transformer is connected to the incomer of the Main L.T Panel.
Instrumental Panel
Instrumentation Contro Panels are designed to monitor and control levels such as temperature flow, current and pressure from the field instruments that are connected to it.
Feeder Pillar Panel (Outdoor)
A feeder pillar, also known as a power box, a distribution pillar, or a feeder pillar box, is a container that is used to- house electrical equipment's. It acts as a central course that controls and distributes electricity to outgoing circuits.
Meter Board
Multi Meter Bus Bar Panel Pre drilled in each corner for fixings. Fire Resistant. Used for mounting electric meters and consumer units. Various sizes available.
Cable Tray & Accessories
Cable trays are mechanical support systems that provide a rigid structural system for electrical cables, raceways, and insulated conductors used for electric power distribution, control, signal instrumentation, and communication.
Bus Ducts & Rising Mains
Bus duct is used in commercial and industrial settings to conduct electricity to power cables or cable bus. Structurally, a bus duct is a sheet metal duct containing either aluminum or copper busbars (metallic strips or bars that conduct a substantial electrical current) in a grounded metal enclosure.
Salient Features
- Bus bars and interlinks are insulated with heat shrinkable PVC sleeves
- Provision for future expansion for both sides
- All live parts are shrouded with polycarbonate sheets
- Customer choice of protection, metering and controlling including SCADA interface
- Single & Double Front Panel (PCC/ MCC /PMCC /MDB)
- Provision for padlocking feeder & bus bar shutters
- Ferrules Machine
- Laser Engraving Machine
- Testing Equipment’s like Megger, Insulation testing, Clamp Meter etc….
- CNC Sheering and Bending Machine
- Hydraulic Busbar Cutting, Bending & punching Machine
- Well Trained Staffs with DEEE & BE(EEE) Qualification
- Design tested at CPRI for short circuit & temperature rise as per IS standards
- Worked with Architect CR Narayana Rao for TNHB Project
- 2500A Panels successfully tested at CPRI for temperature rise as per IS standards
- CNC Fabricated fully bolted standardized designs
- Computer Aided Design (CAD)systems
- Panel enclosure degree of protection IP 54, IP 55 & IP 65
- Anti-corrosion treatment and Sand Blasting Process
- Automatic spray conveyorized Pre-Treatment plant with 7 Tank Process
- Painting in dust & vermin proof paint booths & ovens
- Non hygroscopic SMC bus bar supports for best mechanical & electrical strengths for fault current withstand